Beam-mounted pull-out units

Our pull-out units are supplied ready assembled and fully tested.

Manufacturing happens on site at our ownfactory in Sweden, so we have control of
the whole process. That way we can offeran efficient service and quality

Features

Click the buttons and read more about features

Choose between 70% or 100% extraction capacity

Easy to install – simply secure to the crossbeams using 4 bolts

Maximum loading capacities from 200 kg to 1500 kg per unit

The fact that we use high-quality certified steel with known and consistent properties also contributes to safety

Fitting double ball bearings at the front gives lower
profiles and means that our pull-out units run smoothly with low handling power, even with high load factors.

Our pull-out units are supplied ready
assembled and fully tested.

Beam-mounted (BM) units are mounted on the cross-beams between the pallet racking uprights. The lower frame of the pull-out unit is bolted to the beams and the upper frame slides out carrying the pallet with it.

Pallets may be loaded directly onto the units, but other options allow for storage on open shelving, in plastic bins and in cartons. Being able to pull the units out of the rack allows for safe and easy access to stored items!

BM units are available in a range of capacities up to 1500kg and in a variety of formats to suit your requirements. They can cater for all pallet sizes and types (wood, steel, plastic), front or rear loading at the pallet rack, short or long-side handling, as well as for pallet collars with dividers, containers, bins and loose storage. The base frame BM unit is for pallets.

Video

Units for manual handling

The loading surface consists of a galvanised steel sheet with raised
edges, perfect for Euro crates, boxes, tools etc.

With a wooden frame directly on the unit – you get a economical, quick and effective storage presented in an ergonomical fromat. The wooden frame serves as a powerful and affordable frame that is possible to compartmentalized by dividers.

Unit locks when pushed back into the rack.

Accessories for Beam-mounted units

Click the buttons and read more about accessories

A pull-out unit locking system avoids the danger of the cross-beam
being overloaded. The lock is available for two, three or four pallet-width
bays and locks one section at the time. When one unit is pulled out, the
others are locked. Normally this lock is placed at the back. We also have
a lock that is placed under the unit; this is typically used when there isn’t
enough room behind, for example if you have double pallet racks, or if
you load from the rear.

Rear pallet stop

An angle profile which can be fitted to the back of the unit to stop the pallet sliding too far back when the unit is pushed in. Supplied ready fitted to unit.

Feet for BM unit

For mounting BM units off the floor. Two sizes, for up to 800kg units and up
to 1000kg units. Height 150mm, galvanized steel.

Foot-operated lock release catch Recommended for units installed close to floor level.

Floor mounting profiles
For mounting BM units close to the floor. Three versions,
for short-side and long-side forward handling up to
1000kg, and for short-side handling up to 1500kg.
Height 35mm, galvanized steel.

Lock in extended position
Sometimes you want to lock the unit when it´s pulled out, for example while picking
or loading goods. This lock is also useful with narrow aisles, so that when the unit is
fully pulled out you can load a pallet from the side.

Steel shelf panel
This accessory covers the top of the
pull-out unit so that smaller items such as
plastic bins or cartons can’t slip through.
You can still use the unit for pallets, so you
have fully flexible storage.
Material: Galvanized mild steel

Front pallet stop
A pair of steel plates for mounting either side
of the unit at the front, acts as a safety stop
when loading a pallet from the rear.

Handles for beam-mounted units

The units have integrated horizontal locking handles. Side handles are recommended for BM pull-out units when they are fitted in the lower and mid-range of picking heights, to save bending. Two types are available, Standard and Easy Action™ (EA). Both
types of handle are available in a range of lengths.

Standard handles are simply something to pull on, ideal when a unit is fitted on the
bottom two tiers of the racking. Suitable for all units below 1000kg rating. Supplied separately for fitting by customer.

Easy Action™- (EA) handles use a lever mechanism mounted on ball-bearings to greatly increase the operator’s mechanical advantage. They make it effortless to slide out even a heavily loaded unit. Comes complete mounted on selected unit.

Pull-out capacity Pull-out units

There are three choices to pull out the shelf. The choice of 70% or 100% extension capacity depends mainly on whether or not it’s easy to pick your items from the back of the unit. The choice of one- or two-way action depends on whether you want to load and pick from one side only or to have equal access from both sides..

70% extension one-way

For Best Economy:

For most applications, 70% extension gives sufficientaccess to all your goods

100% extension one-way

For Maximum Access:

If you have small items at the back of the
shelf or if you need to use an overhead
crane for loading and picking, 100%
extension makes life much easier!

70% extension two-way

For Access Both sides:

With shelves that can be pulled out in either direction, you have the possibility of operators at separate work positions accessing the same stores, or at an assembly station one side can be used for picking and the other for restocking.

Number of shelves

The tables show youwhat clearances to expect
between shelves for a given
number of shelves per unit, assuming even spacing. Shelves can also be spaced unevenly ifdesired. For more information, please consult product data sheets or contact us.

Shelf Lock

Unless you bolt the CSU to the floor, it is essential to add a shelf lock, which prevents more than one shelf being pulled out at once, so the unit doesn’t get tipped over

Important Safety Information

  • -The pallet racking must be bolted to the floor (see
    manufactures instructions)
  • -Rear cross beam must be bolted to the pallet racking
    uprights (minimum dimension M8)
  • -The pull-out unit must be bolted to the rear cross-beam
    with the fitting kit provided
  • -Each pair of cross beams must have load capacity
    according to table on next page
  • -Only one pull-out unit in each section (pair of cross
    beams) may be pulled out at a time.
  • -With using pull-out units in different levels of one rack only
    in one level a pull-out unit be pulled-out at the same time
  • -See separate notice for maximum evenly distributed
    loading weight per pull-out unit
  • -Directly after using the pull-out unit, it must be pushed
    back – check that it’s locked!